供应贝斯机电HY-A6工业皮带扣，不散落

供应贝斯机电HY-A6工业皮带扣，不散落

a6型高强度连体皮带扣（强力皮带扣），使用于1400n∕mm及以下高强度输送带的联结，采用特

殊工艺制造，每单元扣体上镶有三组扣钉，错位式扣钉布置，对输送带纤维损伤小，皮带工作时

皮带扣体不易翘头、脱落。每组皮带扣有多个单元体组成，具有抗拉强度大、耐磨损、使用寿命

长等优点，适用于8－14mm运输皮带的联结.

A6连体皮带扣产品特点:

连体式带扣:输送带沿带宽度方向可用一条代扣装订仓储和运输过程中不会造成散落而损耗.

适用带厚范围广:由于钉扣固定带扣后其钉脚能钩回输送带可以一种厚度规格的带扣能满足8-14

毫米厚度的输送带装订联接而方便客户的管理.

A 6 connected belt buckles product features: Connected Belt Buckles: Belt along the 

width direction can be used a buckle binding storage and transportation process does 

not cause scattered and wear and tear. Suitable for a wide range of belt thickness: 

Because the nail pin can hook back the belt after fixing the belt buckle, a belt 

buckle of thickness specification can meet the 8-14 mm thickness of the belt binding 

connection for the convenience of customer management.

接头强度高:由于扣钉呈V型布置使输送带在装订截面上的扣钉的相对密度减少减少对带芯的损伤

输送带运行中带扣的受力分布均匀所以输送根带接头强度高使用寿命长.

接头直线度好:用锤击式订扣机装订将输送带三点式定位后采用交叉次序钉扣使钉扣部位的输送

带挤压变形均匀分布加以连体扣本身平直度好使输送带接头的直线度好联接时便于传入串销运行

时能减少输送带跑偏的原因.

运行中撞击小:低平的板式扣体和呈扇形面并具有导入角扣体前端可减少运行中对托辊滚筒和清

扫器的撞击和磨损.

改善串销的受力:由于采用扣体部位宽扣环结构可减少串销的挤压应力提高串销使用寿命.

High strength of the joint: Because of the v-shaped arrangement of the studs, the 

relative density of the studs on the binding section of the conveyor belt is 

reduced, the damage to the belt core is reduced, and the force on the buckle is 

distributed evenly during the operation of the conveyor belt, so the strength of the 

joint of the conveying root belt is high and the service life is long. The straight 

degree of the joint is good: The belt is fixed by the hammer-impact stapling 

machine. After the belt is fixed in three-point position, the cross-order stapling 

is adopted to make the deformation of the belt at the nail-buckle part extrude 

evenly distributed. The straightness of the joint itself is good so that the 

straight degree of the belt joint is good when the connection is easy to pass 

through the serial pin, the cause of the belt deviation can be reduced when the belt 

runs. Small impact in operation: The low-flat plate fastener and the fan-shaped 

Front end with the leading angle fastener can reduce the impact and wear on roller 

and cleaner in operation. To improve the force of the serial pin: Adopting the wide 

structure of the fastening body can reduce the extrusion stress and prolong the 

service life of the serial